Motorize Your Windows and Skylights!

Wintrol's M2100 Motorizing System for Windows and Skylights is designed to motorize casement, awning, and skylight windows. Don't be fooled by its low profile design and quiet running motor - there are a lot of exciting and powerful features built into this motorizing system.

The built-in flexibility of Wintrol's M2100 Motorizing System will allow you to chose the motor options to meet almost any job requirement. Whether your need is low cost, wireless control, multiple control, or complete automated control, Wintrol's M2100 Motorizing System can be tailored to meet your needs. Wintrol is doing for the windows in your home or office what the automobile industry has done for the windows in your car - except we can make the windows in your home smarter!

FEATURES

No Special Preparation is required by the window manufacturer, making the M2100 Motorizing System suitable for on-site installation on new and existing (retrofit) windows. No field adjustments are required.
Fits Most Crank-Type Operators. The motor design fits onto the existing window operator spline in place of the existing hand crank.
Rain Sensor. The Rain Sensor will automatically close all windows and skylights when moisture is detected. It is included with all LC-II Control Switch Kits.
Sequential Control of up to three skylights or windows without Motorized Locks, or one window with up to two Motorized Locks, is possible from a single LC-I Control Switch or LC-II Control Switch.
Automatic Motor Reversal has been engineered into the LC-I Control Switch and LC-II Control Switch to reverse the motor should an obstruction stop the window while closing.
A Screen Interlock is provided which, when properly installed, electrically disconnects the motor when the screen is removed. The Automatic Motor Reversal and Screen Interlock are intended to help prevent personal injury which could result from reaching into the window area during its operation.
Automatic Compensation For Dirty or Worn Hardware. As the window ages, the operating hardware naturally becomes dirty which makes the window harder to operate. The M2100 Motorizing System automatically compensates for this by reducing the amount of window opening, which is a sign to the homeowner to clean the operating hardware. This also keeps the driving force of the motor components to a minimum until the problem is corrected.
U.L. Listed and C.S.A. Approved. Also meets the requirements for Class II installation.
Control Modules fit a standard single gang electrical box and accept standard decora style cover plates.
Motorized Sash Locks. Motorized Locks are available for use with LC-I Control Switch and LC-II Control Switch for casement and awning windows. Fits most windows.
System Components Are Available Individually to allow maximum ordering flexibility to meet the requirements of any job - large or small. It also allows M2100 Motorizing System features to be easily added at a later date.
Avoid Problems Associated with Power Outages by using commonly available Uninterruptible Power Supplies (UPS) with the M2100 Motorizing System.

CONTROL OPTIONS

The externally controllable LC-II Control Switch has inputs on its motor control module to allow maximum window control flexibility. Each LC-II Control Switch is capable of controlling up to three skylights or windows without Motorized Locks or one window with up to two Motorized Locks. Control flexibility comes from the LC-II Control Switch's inputs and the accessory modules.

The LC-II Control Switch inputs allow the following types of optional controls:

The IR Receiver provides a wireless infrared remote control. The IR Receiver can be connected to control up to 25 LC-II Control Switches which, in turn, can control up to 75 windows. A Rain Sensor input is also provided on the IR Receiver.
The RS Module provides a remote open/close switch. The RS Module can also be connected to control up to 25 LC-II Control Switches which, in turn, can control up to 75 windows. A Rain Sensor input is also provided on the RS Module.
Control Inputs for discrete devices, such as a thermostat, are provided. These inputs are designed to be activated by any SPST (single pole, single throw) switch or sensor suitable for low voltage applications. Each discrete device can be connected to control up to 25 LC-II Control Switches.
Home Automation Systems, including X-10 ®, can also be connected to the LC-II Control Switch to provide full control of the M2100 Motorizing System.
Close & Hold is an input that, when activated, closes all windows and ignores all other inputs. This input is intended for use with security systems when it is necessary to have an overriding control. This input can be activated by any SPST switch or sensor suitable for low voltage applications.
Open & Hold is an input that, when activated, opens all windows and ignores all other inputs. This input can be activated by any SPST switch or sensor suitable for low voltage applications. This input has priority over Close & Hold.

The LC-II Control Switch also has an output which sends a signal when the window is closed or not closed. This output is not intended to replace window position information for security purposes.

CONSUMER NOTICE

Wintrol's M2100 Motorizing System for Windows and Skylights must be installed by a qualified electrician.

WARNING: To help prevent personal injury from moving window parts, an inside screen applied to any motorized window must have the provided screen interlock properly installed. Proper installation is the responsibility of the installer.

Wintrol developed this window motorizing system that was subsequently licensed to Truth Hardware in Owatonna, Minnesota. Truth Hardware is currently the sole producer of the product and markets it under the Truth Sentry 2000 brand name. Wintrol has retained certain marketing rights, producing several installation kits and covers for applications where we can offer a more tailored and aesthetic installation.

All M2100 Motorizing Systems are warranted by Truth Hardware for a one year component replacement term.

INCLUDE WINTROL SPECS IN YOUR NEXT WINDOW AUTOMATION PROJECT

Motorizing system for casement, awning, or skylight windows. Mounting should accommodate wood, PVC, or metal windows.

Motorizing system shall replace the handle on crank type casement, awning, or skylight windows operators. The motor drive to be constructed of a high pressure zinc die cast housing, containing hardened steel drive gears and a high torque 24 VDC motor. Interchangeable drive adapter allows the system to be compatible with all Truth operators and some other window hardware systems not manufactured by Truth.

Mounting hardware to be provided to accommodate a wide range of window profile shapes and materials. Unit to be supplied with a decorative plastic cover which allows convenient access to mechanical components and easy installation. The wall mounted motor control module fits a standard single gang electrical box and allows the use of standard decora-style switch cover plates. The motor control module is to be supplied with color matching buttons to allow color coordination with cover plate. The control circuitry shall control up to three motors in standard form. Motor system kit includes: motor drive, decorative cover, wall switch, cover plate, transformer, and mounting hardware.

This motor system shall be "M2100 Motorizing System for Windows and Skylights" series as distributed by Win-Trol, Inc., Helena, Montana.